12V NE555 PWM Controller Under $3 Mais. How to make a mini inverter 1.5v dc to 220v ac with an old mobile phone charger TRANSFORMATOR. 'DIY Tesla Slayer. Nov 19, 2014  My first small Tesla coil with NE555 and flyback transformer. This is my first Tesla coil.It's not completed yet actually. Now all I need is to produce constant sparks off the top of the coil without touching a screwdriver or a lamp!

Here I've used two separate power supplies-a 6V powering the NE555 and a 12V powering the 2N3055 and the flyback.I've also used a COSMO 1010 (C1010) photocoupler to make sure that the NE555 doesnt blow from the 12volt supply. The coil The secondary coil has about 400 turns of 0.4mm magnet wire wrapped around a 3cm paper roll.The primary is 5 turns of speaker wire. The spark gap Just two screws not attached to anything facing each other. Capacitor bank Here are the capacitors I've used: 5̶3̶2̶J̶,̶ ̶4̶7̶4̶J̶,̶ ̶.̶2̶7̶J̶ ̶,̶ ̶.̶6̶4̶J̶,̶ ̶.̶2̶2̶J̶,̶ ̶1̶0̶5̶J̶,̶1̶2̶4̶J̶,̶ ̶8̶2̶2̶J̶/̶1̶.̶6̶K̶V̶.̶M̶o̶s̶t̶ ̶o̶f̶ ̶t̶h̶e̶ ̶o̶t̶h̶e̶r̶ ̶c̶a̶p̶s̶ ̶a̶r̶e̶ ̶r̶a̶t̶e̶d̶ ̶4̶0̶0̶V̶o̶l̶t̶s̶ ̶I̶ ̶t̶h̶i̶n̶k̶.̶O̶n̶e̶ ̶o̶r̶ ̶t̶w̶o̶ ̶2̶0̶0̶V̶o̶l̶t̶s̶.̶ S̶o̶ ̶,̶i̶f̶ ̶m̶y̶ ̶c̶a̶l̶c̶u̶l̶a̶t̶i̶o̶n̶s̶ ̶a̶r̶e̶ ̶c̶o̶r̶r̶e̶c̶t̶ ̶t̶h̶e̶n̶ ̶t̶h̶e̶ ̶b̶a̶n̶k̶ ̶s̶h̶o̶u̶l̶d̶ ̶b̶e̶ ̶a̶b̶o̶u̶t̶ ̶4̶K̶V̶o̶l̶t̶s̶ ̶a̶n̶d̶ ̶9̶0̶0̶ ̶p̶F̶s̶.̶. The calculations were wrong -this was too much capacitance.I've replaced this chain of capacitors with a single DIY aluminum foil and plastic sheets as dielectric capacitor.I am not aware of the capacitance value of this though.I do not own an LC meter. Here is how I made this homebrew capacitor. Maybe the bank is not good enough for spark on top.Maybe the bank is the culprit.

How to get the constant spark on top? I know it has something to to do with resonance.Obviously there is no resonance here. Here I've used two separate power supplies-a 6V powering the NE555 and a 12V powering the 2N3055 and the flyback.I've also used a COSMO 1010 (C1010) photocoupler to make sure that the NE555 doesnt blow from the 12volt supply.

The coil The secondary coil has about 400 turns of 0.4mm magnet wire wrapped around a 3cm paper roll.The primary is 5 turns of speaker wire. The spark gap Just two screws not attached to anything facing each other. Capacitor bank Here are the capacitors I've used: 5̶3̶2̶J̶,̶ ̶4̶7̶4̶J̶,̶ ̶.̶2̶7̶J̶ ̶,̶ ̶.̶6̶4̶J̶,̶ ̶.̶2̶2̶J̶,̶ ̶1̶0̶5̶J̶,̶1̶2̶4̶J̶,̶ ̶8̶2̶2̶J̶/̶1̶.̶6̶K̶V̶.̶M̶o̶s̶t̶ ̶o̶f̶ ̶t̶h̶e̶ ̶o̶t̶h̶e̶r̶ ̶c̶a̶p̶s̶ ̶a̶r̶e̶ ̶r̶a̶t̶e̶d̶ ̶4̶0̶0̶V̶o̶l̶t̶s̶ ̶I̶ ̶t̶h̶i̶n̶k̶.̶O̶n̶e̶ ̶o̶r̶ ̶t̶w̶o̶ ̶2̶0̶0̶V̶o̶l̶t̶s̶.̶ S̶o̶ ̶,̶i̶f̶ ̶m̶y̶ ̶c̶a̶l̶c̶u̶l̶a̶t̶i̶o̶n̶s̶ ̶a̶r̶e̶ ̶c̶o̶r̶r̶e̶c̶t̶ ̶t̶h̶e̶n̶ ̶t̶h̶e̶ ̶b̶a̶n̶k̶ ̶s̶h̶o̶u̶l̶d̶ ̶b̶e̶ ̶a̶b̶o̶u̶t̶ ̶4̶K̶V̶o̶l̶t̶s̶ ̶a̶n̶d̶ ̶9̶0̶0̶ ̶p̶F̶s̶.̶. The calculations were wrong -this was too much capacitance.I've replaced this chain of capacitors with a single DIY aluminum foil and plastic sheets as dielectric capacitor.I am not aware of the capacitance value of this though.I do not own an LC meter. Here is how I made this homebrew capacitor. Software cracks keygens. Maybe the bank is not good enough for spark on top.Maybe the bank is the culprit.

In order to provide the best platform for continued innovation, Jive no longer supports Internet Explorer 7. Jive will not function with this version of Internet Explorer.